Second time’s the charm:
There’s not much difference from the first iteration, apart from a few code cleanups. The engraved text is kinda-sorta gratuitous, but I figured having the circuit board dimensions on all the key parts would avoid heartache & confusion; the code now autosizes the board to the holder OD. Skeletonizing the board template didn’t save nearly as much printing time as I expected, though.
Now I can build a second electrometer amp without dismantling the two-transistor version.
The OpenSCAD source code:
// Victoreen 710-104 Ionization Chamber Fittings
// Ed Nisley KE4ZNU August 2015
Layout = "Show";
// Show - assembled parts
// Build - print can parts + shield
// BuildShield - print just the shield
// BuildHolder - print just the can cap & PCB base
// CanCap - PCB insulator for 6-32 mounting studs
// CanBase - surrounding foot for ionization chamber
// CanRim - generic surround for either end of chamber
// PCB - template for cutting PCB sheet
// PCBBase - holder for PCB atop CanCap
// Shield - electrostatic shield shell
//- Extrusion parameters must match reality!
// Print with 2 shells and 3 solid layers
ThreadThick = 0.25;
ThreadWidth = 0.40;
HoleWindage = 0.2;
Protrusion = 0.1; // make holes end cleanly
AlignPinOD = 1.75; // assembly alignment pins = filament dia
inch = 25.4;
function IntegerMultiple(Size,Unit) = Unit * ceil(Size / Unit);
//- Screw sizes
Tap4_40 = 0.089 * inch;
Clear4_40 = 0.110 * inch;
Head4_40 = 0.211 * inch;
Head4_40Thick = 0.065 * inch;
Nut4_40Dia = 0.228 * inch;
Nut4_40Thick = 0.086 * inch;
Washer4_40OD = 0.270 * inch;
Washer4_40ID = 0.123 * inch;
//----------------------
// Dimensions
OD = 0; // name the subscripts
LENGTH = 1;
Chamber = [91.0,38]; // Victoreen ionization chamber dimensions
Stud = [ // stud welded to ionization chamber lid
[6.5,IntegerMultiple(0.8,ThreadThick)], // flat head -- generous clearance
[4.0,9.5], // 6-32 screw -- ditto
];
NumStuds = 3; // this really isn't much of a variable...
StudAngle = 360/NumStuds;
StudSides = 6; // for hole around stud
BCD = 2.75 * inch; // mounting stud bolt circle diameter
PlateThick = 2.0; // minimum layer atop and below chamber ends
RimHeight = 4.0; // extending along chamber perimeter
WallHeight = RimHeight + PlateThick;
WallThick = 3.0; // thick enough to be sturdy & printable
CapSides = 8*6; // must be multiple of 4 & 3 to make symmetries work out right
RimOD = Chamber[OD] + 2*WallThick;
echo(str("Rim OD: ",RimOD));
//PCBFlatsOD = 82.0; // desired hex dia flat-to-flat
PCBFlatsOD = floor(RimOD*cos(30)) - 2.0; // .. maximum possible
//PCBFlatsOD = floor(Chamber[OD]*cos(30)) - 2.0; // .. chamber fitting
PCBClearance = ThreadWidth; // clearance beyond each flat for mounting
PCBThick = 1.1;
PCBActual = [PCBFlatsOD/cos(30),PCBThick]; // OD = tip-to-tip
PCBCutter = [(PCBFlatsOD + 2*PCBClearance)/cos(30),PCBThick - ThreadThick]; // OD = tip-to-tip dia + clearance
PCBSize = str(PCBFlatsOD, " mm");
echo(str("Actual PCB across flats: ",PCBFlatsOD));
echo(str(" ... tip-to-tip dia: ",PCBActual[OD]));
echo(str(" ... thickness: ",PCBActual[LENGTH]));
HolderHeight = 13.0 + PCBCutter[LENGTH]; // thick enough for PCB to clear studs + batteries
HolderShelf = 2.0; // shelf under PCB edge
HolderTrim = 5.0; // remove end of holder to clear PCB edge solder blobs
echo(str("Holder trim distance: ",HolderTrim));
HolderTrimAngle = StudAngle/2 - 2*atan(HolderTrim*cos(StudAngle/2)/(PCBActual[OD]/2)); // atan is close for small angles
echo(str(" ... angle: ",HolderTrimAngle));
PinAngle = 15; // alignment pin angle on either side of holder screw
echo(str("PCB holder across flats: ",PCBCutter[OD]*cos(30)));
echo(str(" ... height: ",HolderHeight));
ShieldInset = 0.5; // shield inset from actual PCB flat
ShieldWall = 2.0; // wall thickness
ShieldLid = 6*ThreadThick; // top thickness (avoid one infill layer)
Shield = [(PCBFlatsOD - 2*ShieldInset)/ cos(30),40.0]; // electrostatic shield shell dimensions
TextSize = 4;
TextCharSpace = 1.05;
TextLineSpace = TextSize + 2;
TextDepth = 1*ThreadThick;
//----------------------
// Useful routines
module PolyCyl(Dia,Height,ForceSides=0) { // based on nophead's polyholes
Sides = (ForceSides != 0) ? ForceSides : (ceil(Dia) + 2);
FixDia = Dia / cos(180/Sides);
cylinder(r=(FixDia + HoleWindage)/2,
h=Height,
$fn=Sides);
}
//- Locating pin hole with glue recess
// Default length is two pin diameters on each side of the split
module LocatingPin(Dia=AlignPinOD,Len=0.0) {
PinLen = (Len != 0.0) ? Len : (4*Dia);
translate([0,0,-ThreadThick])
PolyCyl((Dia + 2*ThreadWidth),2*ThreadThick,4);
translate([0,0,-2*ThreadThick])
PolyCyl((Dia + 1*ThreadWidth),4*ThreadThick,4);
translate([0,0,-Len/2])
PolyCyl(Dia,Len,4);
}
module ShowPegGrid(Space = 10.0,Size = 1.0) {
RangeX = floor(100 / Space);
RangeY = floor(125 / Space);
for (x=[-RangeX:RangeX])
for (y=[-RangeY:RangeY])
translate([x*Space,y*Space,Size/2])
%cube(Size,center=true);
}
//-----
module CanRim(BaseThick) {
difference() {
cylinder(d=Chamber[OD] + 2*WallThick,h=(WallHeight + BaseThick),$fn=CapSides);
translate([0,0,BaseThick])
PolyCyl(Chamber[OD],Chamber[LENGTH],CapSides);
}
}
module CanCap() {
difference() {
CanRim(PlateThick + Stud[0][LENGTH]);
translate([0,0,-Protrusion]) // central cutout
rotate(180/6)
cylinder(d=BCD,h=Chamber[LENGTH],$fn=6); // ... reasonable size
for (i=[0:(NumStuds - 1)]) // stud clearance holes
rotate(i*StudAngle)
translate([BCD/2,0,0])
rotate(180/StudSides) {
translate([0,0,PlateThick])
PolyCyl(Stud[0][OD],Chamber[LENGTH],StudSides);
translate([0,0,-Protrusion])
PolyCyl(Stud[1][OD],Chamber[LENGTH],StudSides);
}
for (i=[0:(NumStuds - 1)], j=[-1,1]) // PCB holder alignment pins
rotate(i*StudAngle + j*PinAngle + 60)
translate([Chamber[OD]/2,0,0])
rotate(180/4 - j*PinAngle)
LocatingPin(Len=2*(PlateThick + Stud[0][LENGTH]) - 4*ThreadThick);
translate([-(BCD/2),0,-Protrusion])
rotate(90) mirror()
linear_extrude(height=(ThreadThick + Protrusion))
text(PCBSize,size=6,font="Liberation Mono:style=bold",halign="center",valign="center");
}
}
module CanBase() {
difference() {
CanRim(PlateThick);
translate([0,0,-Protrusion])
PolyCyl(Chamber[OD] - 2*RimHeight,Chamber[LENGTH],CapSides);
}
}
module PCBTemplate() {
CutLen = 10*PCBActual[LENGTH];
difference() {
cylinder(d=PCBActual[OD],h=PCBActual[LENGTH],$fn=6); // actual PCB size
translate([0,0,-Protrusion])
cylinder(d=8,h=CutLen,$fn=12);
if (true)
for (i=[0:5]) // empirical cutouts
rotate(i*60 + 30)
translate([PCBFlatsOD/3,0,-Protrusion])
rotate(60)
cylinder(d=0.43*PCBActual[OD],h=CutLen,$fn=3);
translate([PCBActual[OD]/4,0,(PCBActual[LENGTH] - ThreadThick)])
linear_extrude(height=(ThreadThick + Protrusion),convexity=1)
text(PCBSize,size=4,font="Liberation Mono:style=bold",halign="center",valign="center");
}
}
module PCBBase() {
intersection() {
difference() {
cylinder(d=Chamber[OD] + 2*WallThick,h=HolderHeight,$fn=CapSides); // outer rim
rotate(30) {
translate([0,0,-Protrusion]) // central hex
cylinder(d=(PCBActual[OD] - HolderShelf/cos(30) - HolderShelf/cos(30)),h=2*HolderHeight,$fn=6);
translate([0,0,HolderHeight - PCBCutter[LENGTH]]) // hex PCB recess
cylinder(d=PCBCutter[OD],h=HolderHeight,$fn=6);
for (i=[0:NumStuds - 1]) // PCB retaining screws
rotate(i*StudAngle + 180/(2*NumStuds))
translate([(PCBCutter[OD]*cos(30)/2 + Clear4_40/2 + ThreadWidth),0,-Protrusion])
rotate(180/6)
PolyCyl(Tap4_40,2*HolderHeight,6);
for (i=[0:(NumStuds - 1)], j=[-1,1]) // PCB holder alignment pins
rotate(i*StudAngle + j*PinAngle + 180/(2*NumStuds))
translate([Chamber[OD]/2,0,0])
rotate(180/4 - j*PinAngle)
LocatingPin(Len=2*(HolderHeight - 4*ThreadThick));
}
if (false)
for (i=[0:NumStuds - 1])
rotate(i*StudAngle - StudAngle/2) // segment isolation - hex sides
translate([0,0,-Protrusion]) {
linear_extrude(height=2*HolderHeight)
polygon([[0,0],[Chamber[OD],0],[Chamber[OD]*cos(180/NumStuds),Chamber[OD]*sin(180/NumStuds)]]);
}
translate([-(PCBFlatsOD/2 + PCBClearance - HolderShelf),0,HolderHeight/2])
rotate([0,90,0]) rotate(90)
linear_extrude(height=(ThreadWidth + Protrusion))
text(PCBSize,size=6,font="Liberation Mono:style=bold",halign="center",valign="center");
}
for (i=[0:NumStuds - 1])
rotate(i*StudAngle + StudAngle/2 - HolderTrimAngle/2) // trim holder ends
translate([0,0,-Protrusion]) {
linear_extrude(height=2*HolderHeight)
polygon([[0,0],[Chamber[OD],0],[Chamber[OD]*cos(HolderTrimAngle),Chamber[OD]*sin(HolderTrimAngle)]]);
}
}
}
//-- Electrostatic shield
// the cutouts are completely ad-hoc
module ShieldShell() {
CutHeight = 7.0;
difference() {
cylinder(d=Shield[OD],h=Shield[LENGTH],$fn=6); // exterior shape
translate([0,0,-ShieldLid]) // interior
cylinder(d=(Shield[OD] - 2*ShieldWall/cos(30)),h=Shield[LENGTH],$fn=6);
translate([0,0,Shield[LENGTH] - TextDepth])
rotate(180) {
translate([0,0.3*Shield[OD] - 0*TextLineSpace,0])
linear_extrude(height=(TextDepth + Protrusion))
text("Gamma",size=TextSize,spacing=TextCharSpace,font="Liberation:style=bold",halign="center",valign="center");
translate([0,0.3*Shield[OD] - 1*TextLineSpace,0])
linear_extrude(height=(TextDepth + Protrusion))
text("Ionization",size=TextSize,spacing=TextCharSpace,font="Liberation:style=bold",halign="center",valign="center");
translate([0,0.3*Shield[OD] - 2*TextLineSpace,0])
linear_extrude(height=(TextDepth + Protrusion))
text("Amplifier",size=TextSize,spacing=TextCharSpace,font="Liberation:style=bold",halign="center",valign="center");
translate([0,-0.3*Shield[OD] + 1*TextLineSpace,0])
linear_extrude(height=(TextDepth + Protrusion))
text("KE4ZNU",size=TextSize,spacing=TextCharSpace,font="Liberation:style=bold",halign="center",valign="center");
translate([0,-0.3*Shield[OD] + 0*TextLineSpace,0])
linear_extrude(height=(TextDepth + Protrusion))
text("2015-08",size=TextSize,spacing=TextCharSpace,font="Liberation:style=bold",halign="center",valign="center");
}
translate([Shield[OD]/4 - 20/2,Shield[OD]/2,(CutHeight - Protrusion)/2]) // switch
rotate(90)
cube([Shield[OD],20,CutHeight + Protrusion],center=true);
if (false)
translate([-Shield[OD]/4 + 5/2,Shield[OD]/2,(CutHeight - Protrusion)/2]) // front
rotate(90)
cube([Shield[OD],5,CutHeight + Protrusion],center=true);
translate([-Shield[OD]/2,0,(CutHeight - Protrusion)/2]) // right side
cube([Shield[OD],7,CutHeight + Protrusion],center=true);
translate([0,(Shield[OD]*cos(30)/2 - ThreadWidth),0.75*Shield[LENGTH]])
rotate([90,0,180]) rotate(00)
linear_extrude(height=(ThreadWidth + Protrusion))
text(PCBSize,size=5,font="Liberation Mono:style=bold",halign="center",valign="center");
}
}
//----------------------
// Build it
ShowPegGrid();
if (Layout == "CanRim") {
CanRim();
}
if (Layout == "CanCap") {
CanCap();
}
if (Layout == "CanBase") {
CanBase();
}
if (Layout == "PCBBase") {
PCBBase();
}
if (Layout == "PCB") {
PCBTemplate();
}
if (Layout == "Shield") {
ShieldShell();
}
if (Layout == "Show") {
CanBase();
color("Orange",0.5)
translate([0,0,PlateThick + Protrusion])
cylinder(d=Chamber[OD],h=Chamber[LENGTH],$fn=CapSides);
translate([0,0,(2*PlateThick + Chamber[LENGTH] + 2*Protrusion)])
rotate([180,0,0])
CanCap();
translate([0,0,(2*PlateThick + Chamber[LENGTH] + 5.0)])
PCBBase();
color("Green",0.5)
translate([0,0,(2*PlateThick + Chamber[LENGTH] + 7.0 + HolderHeight)])
rotate(30)
PCBTemplate();
translate([0,0,(2*PlateThick + Chamber[LENGTH] + 15.0 + HolderHeight)])
rotate(-30)
ShieldShell();}
if (Layout == "Build") {
translate([-0.50*Chamber[OD],-0.60*Chamber[OD],0])
CanCap();
if (false)
translate([0.55*Chamber[OD],-0.60*Chamber[OD],0])
rotate(30)
translate([0,0,Shield[LENGTH]])
rotate([0,180,0])
ShieldShell();
if (true)
translate([0.55*Chamber[OD],-0.60*Chamber[OD],0])
rotate(30)
PCBTemplate();
if (true)
translate([-0.25*Chamber[OD],0.60*Chamber[OD],0])
CanBase();
translate([0.25*Chamber[OD],0.60*Chamber[OD],0])
PCBBase();
}
if (Layout == "BuildHolder") {
translate([-0.25*Chamber[OD],0,0])
CanCap();
translate([0.25*Chamber[OD],0,0])
PCBBase();
}
if (Layout == "BuildShield") {
translate([0,0,Shield[LENGTH]])
rotate([0,180,0])
ShieldShell();
}
The Smell of Molten Projects in the Morning 
Comments
2 responses to “Victoreen 710-104 Ionization Chamber: Revised Fittings”
[…] A bit less than a month later, after producing several iterations of unrelated doodads: […]
[…] The alignment pin holes between the ionization can lid and the board supports: […]