Category: Home Ec

Things around the home & hearth

Laser Cutter: Fourth Corner Fix Summary
A discussion on the LightBurn forum about a large-format machine with a misaligned beam prompted me to think through the whole “Fourth Corner” problem and come up with this summary based on my beam realignment adventure:
Here’s what I think is going on, referring to the 4×8 foot (!) machine in that discussion and lightly edited to improve readability & fix minor errors …

Mirror 1 alignment gets the beam parallel to the Y axis, averaged over the gantry travel between front and rear. The path length variation on your machine is four feet.

Mirror 2 alignment gets the beam parallel to the X axis, averaged over the laser head travel from left to right. The path length variation on your machine is eight feet.

When the laser head is in the left rear corner, the total path length is maybe a foot or two. When it’s in the front right corner, the total path length is upwards of twelve feet.

The “Fourth Corner” problem comes from a slight angular misalignment of Mirror 1, because you (and I and everybody) must set it with a maximum path length around four feet (Mirror 1 to Mirror 2 with the gantry at the front end of the machine). But with the laser head in the right front corner, the path length (Mirror 1 to Mirror 3) is three times longer, so the error due to a slightly mis-set angle at Mirror 1 is correspondingly larger.

A tiny tweak to Mirror 1 changes the spot position at Mirror 2 by very little, but moves the spot at Mirror 3 by much more due to the longer path length.

Tweaking Mirror 1 cannot compensate for a warped machine frame, but it will get the beam alignment as good as it can be made.

The next point of contention was my “middle of the mirror” suggestion. AFAICT, the spot burned into the target at each mirror marks only the useful part of the beam with stray energy in a halo around it. Centering the spot keeps that stray energy away from the mirror mounts, so it doesn’t cause unnecessary heating. This will be particularly important with a high-power laser.

Angular adjustment of each mirror puts the beam parallel to the axes, but cannot also center it on the mirrors. After it’s aligned, the path from the laser tube through the nozzle depends on the position of the tube relative to the nozzle: moving the tube up/down and front/back moves the beam position on the mirrors and through the nozzle, but (in an ideal world) doesn’t change the angular alignment.

So after aligning the beam parallel to the axes, you must move the laser tube, the mirrors (up/down left/right front/back), and maybe the laser head to center the beam in the mirrors and also in the nozzle. Because we don’t live in an ideal world, moving any of those pieces wrecks their angular alignment, so it’s an iterative process.

The goal is to reach this point:

Beam Alignment – Mirror 3 detail – 2023-09-16

Those are five separate pulses, one each at the four corners and center of the platform.

The beam then goes pretty much through the center of the laser head and lens:

Beam Alignment – Focus detail – 2023-09-16

Works for me, anyhow.
2024-11-13
Layered Paper: Mariner’s Compass in Colors

Having recently shotgunned Amazon’s selection of colored art paper, this becomes possible:

Mariners Compass – inset browns

It’s the same geometry as the plain white layered version, with somewhat more attention to detail, and consists of a dozen layers glued and stacked on an assembly fixture.

The quilt-block version uses simple layering:

Layered Paper – Mariners Compass – Beyer 133

No commercial potential, but I like the effect.

2024-11-12
The Good Old Days Weren’t: Arsenical Poisons

An entry from The New Garden Encylopedia, copyright 1936 through 1946, gives recommendations for using arsenical poisons in your garden:

Arsenical poisons

My father always said anybody who talks fondly of The Good Old Days wasn’t alive back then. He was and thought things had definitely improved since then.

Words to live by.

2024-11-11

Wire Plant Stand Feet

A pair of plant stands from a friend’s collection ended up in Mary’s care and cried out for feet to keep their welded steel wire legs from scratching the floor:

Admittedly, it’s not the prettiest stand you can imagine, but the sentimental value outweighs all other considerations.

The feet are shrink-wrapped around the legs with enough curviness to look good:

Wire plant stand feet - show side view — Wire plant stand feet – show side view

With a drain hole in the bottom to prevent water from rusting the wires any more than they already are:

Wire plant stand feet - show bottom view — Wire plant stand feet – show bottom view

I briefly considered a flat bottom at the proper angle to sit on the floor, but came to my senses; it would never sit at the proper angle.

The end results snapped into place:

Wire plant stand feet - indoor detail — Wire plant stand feet – indoor detail

Of course the other stand, at first glance identical to the one above, has a different wire size and slightly different geometry, which I only discovered after printing another trio of feet. Changing the appropriate constants in the OpenSCAD program and waiting an hour produced a better outcome:

Wire plant stand feet - outdoor stand — Wire plant stand feet – outdoor stand

Living in the future is good, all things considered.

The OpenSCAD code as a GitHub Gist:

	// Wire plant stand feet
	// Ed Nisley KE4ZNU
	// 2024-11-06

	Layout = "Show"; // [Show,Build,Leg,LegPair,FootShell,Foot,Section]

	/* [Hidden] */

	ID = 0;
	OD = 1;
	LENGTH = 2;

	TOP = 0;
	BOT = 1;

	FootLength = 30.0; // vertical foot length

	LegRings = // [255.0,350.0,300.0]; // top dia, bottom dia, vertical height
	[260.0,312.0,300.0];

	WireOD = //4.6 + 0.4; // oversize to handle bent legs
	5.7 + 1.0;

	DrainOD = 4.0; // drain hole in the bottom

	LegWidth = // [65.0,9.7]; // outer width at top & bottom
	[95.0, 12.0];

	LegAngle = atan((LegWidth[TOP] – LegWidth[BOT])/(2*LegRings[LENGTH]));

	StandAngle = atan((LegRings[TOP] – LegRings[BOT])/(2*LegRings[LENGTH]));

	WallThick = 3.0;

	FootWidth = 2*[WallThick,WallThick] +
	[LegWidth[BOT] + LegWidth[TOP]*FootLength/LegRings[LENGTH],LegWidth[BOT]];
	echo(FootWidth=FootWidth);

	NumSides = 234;

	Protrusion = 0.1;

	//—– Set up pieces

	module Leg() {

	hull()
	for (k = [0,1])
	translate([0,0,k*LegRings[LENGTH]])
	sphere(d=WireOD,$fn=NumSides);
	}

	module LegPair() {

	for (i = [-1,1])
	translate([i*(LegWidth[BOT] – WireOD)/2,0,0])
	rotate([0,i*LegAngle,0])
	rotate(180/NumSides)
	Leg();
	hull() // simulate weld for flat bottom
	for (i = [-1,1])
	translate([i*(LegWidth[BOT] – WireOD)/2,0,0])
	rotate([0,i*LegAngle,0])
	rotate(180/NumSides)
	sphere(d=WireOD,$fn=NumSides);
	}

	module FootShell() {

	difference() {
	hull() {
	for (i = [-1,1]) {
	translate([i*((FootWidth[BOT] – WireOD)/2 – WallThick),0,0])
	rotate(180/NumSides)
	sphere(d=(WireOD + 2*WallThick),$fn=NumSides);

	translate([i*((FootWidth[TOP] – WireOD)/2 – WallThick),0,FootLength – WireOD/2])
	rotate(180/NumSides)
	sphere(d=(WireOD + 2*WallThick),$fn=NumSides);
	}
	}
	translate([0,0,FootLength + FootLength/2])
	cube([2FootWidth[TOP],10WallThick,FootLength],center=true);
	rotate(180/NumSides)
	cylinder(d=DrainOD,h=4*FootLength,center=true,$fn=NumSides);
	}
	}

	module Foot() {

	difference() {

	FootShell();
	hull()
	LegPair();

	}

	}

	//—– Build it

	if (Layout == "Leg")
	Leg();

	if (Layout == "LegPair")
	LegPair();

	if (Layout == "FootShell")
	FootShell();

	if (Layout == "Foot")
	Foot();

	if (Layout == "Section")
	difference() {
	Foot();
	cube([FootWidth[TOP],(WireOD + 2WallThick),2FootLength],center=false);
	}

	if (Layout == "Show") {
	rotate([StandAngle,0,0]) {
	Foot();
	color("Green",0.5)
	LegPair();
	}
	}

	if (Layout == "Build")
	translate([0,0,FootLength])
	rotate([0*(90-StandAngle),180,0])
	Foot();

view raw Wire plant stand feet.scad hosted with ❤ by GitHub

2024-11-08

Curtain Rod Spring Pusher Block

Spotted during Autumn Window Cleaning:

Curtain rod pusher block – spring contortion

That’s the compression spring inside the curtain rod over the kitchen sink, intended to push the ends against the cabinets on either side. The screw slides along the outer rod and when tightened, backstops the spring against the inner rod.

The end of the spring is apparently intended to twist and jam inside the inner half of the rod, but that seemed so … unesthetic.

Being in the midst of setting up a Windows 11 box for the laser cutter, I used it as an excuse to fiddle with the RDP configuration to get LightBurn running in full screen mode on the monitor atop my desk; more about all that later.

The little pusher block is a hull around a pair of circles the same diameter as the smaller dimension of the inner rod, spaced apart enough to match its width, then laser-cut from a scrap of 1/4 inch acrylic:

Curtain rod pusher block – overview

Which assembles as you’d expect:

Curtain rod pusher block – installed

The spring seems much happier pushing against the block, doesn’t it?

Admittedly, this was completely unnecessary, but if you think of it as a side effect of the Win 11 thing, it makes at least a little sense.

2024-11-07
Sears Humidifier: Bottle Patching

Although the Sears humidifier (Model 758.154200 if you’re keeping score) that Came With The House™ works fine with its lid hinges broken, Mary heard an odd hissing sound somewhere inside. The sound continued with the thing unplugged and, after a protracted struggle in the kitchen sink, we tracked the sound to a crack in one of the dimples joining the front and back faces of the right-side water bottle:

Sears Humidifier bottle – overview

The vertical shaded bars come from the camera’s electronic shutter vs. unfiltered 60 Hz AC powering the shop LED lights.

Unsurprisingly, replacement bottles are no longer available, although you can get fill caps and valves, plus wicking filters.

A water drop squeezed in the crack:

Sears Humidifier bottle – crack

The bottles are polyethylene that sneers at any normal sealant, but I have a few square inches of tape intended for repairs exposed to weather. I didn’t get the snippet aligned just as I wanted, but its gooey adhesive definitely covered the crack:

Sears Humidifier bottle – patched

The bottles normally operate with a slight vacuum, thus the air hissing through the crack, so the tape need not withstand any continuous pressure and the adhesive layer should flow into the crack if it goes anywhere at all.

Protip: the gooey adhesive bonds instantly and irrevocably to whatever it touches, so do a trial fit before you peel off the backing tape.

If the “Serial” is a date code, it’s been around for while:

Sears Humidifier – data plate

It should be good for a few more decades …

2024-11-06
Laser Test Paper: Weathering

Three months of outdoor exposure suggest that laser test paper can survive use as a plant tag for one growing season, at least when it remains flat:

Laser test paper – small plant labels – 3 month exposure

The two upper tags demonstrated the paper has no flexibility worth mentioning, so it cannot become a tag wrapped around a stem.

The two lower labels spent their time tucked into a window frame where they got plenty of sun & rain without the benefit of a backing plate. Looks good to me!

Contrary to my expectation, the craft adhesive sheet behind this label survived intact, although the label itself took some damage, perhaps from the more direct sunlight out on the deck:

Laser test paper – plant marker – 3 month exposure

In any event, they look Good Enough™ for our simple needs and next year’s plants will be properly labeled.

2024-11-04