The New Hotness

After five gardening seasons, my simple 3D printed wrench broke:

Hose Valve Knob - fractured — Hose Valve Knob – fractured

Although Jason’s comment suggesting carbon-fiber reinforcing rods didn’t prompt me to lay in a stock, ordinary music wire should serve the same purpose:

Hose Valve Knob - cut pins — Hose Valve Knob – cut pins

The pins are 1.6 mm diameter and 20 mm long, chopped off with hardened diagonal cutters. Next time, I must (remember to) grind the ends flat.

The solid model needs holes in appropriate spots:

Hose Valve Knob - Reinforced - Slic3r — Hose Valve Knob – Reinforced – Slic3r

Yes, I’m going to put round pins in square holes, without drilling the holes to the proper diameter: no epoxy, no adhesive, just 20 mm of pure friction.

The drill press aligns the pins:

Hose Valve Knob - pin ready — Hose Valve Knob – pin ready

And rams them about halfway down:

Hose Valve Knob - pin midway — Hose Valve Knob – pin midway

Close the chuck jaws and shove them flush with the surface:

Hose Valve Knob - pins installed — Hose Valve Knob – pins installed

You can see the pins and their solid plastic shells through the wrench stem:

Hose Valve Knob - assembled — Hose Valve Knob – assembled

Early testing shows the reinforced wrench works just as well as the previous version, even on some new valves sporting different handles, with an equally sloppy fit for all. No surprise: I just poked holes in the existing model and left all the other dimensions alone.

The OpenSCAD source code as a GitHub Gist:

	// Hose connector knob
	// Ed Nisley KE4ZNU – June 2015
	// 2020-05 add reinforcing rods

	Layout = "Build"; // [Knob, Stem, Show, Build]

	RodHoles = true;

	//- Extrusion parameters – must match reality!

	/* [Hidden] */

	ThreadThick = 0.25;
	ThreadWidth = 0.40;

	function IntegerMultiple(Size,Unit) = Unit * ceil(Size / Unit);

	Protrusion = 0.1;

	HoleWindage = 0.2;

	//——
	// Dimensions

	/* [Dimensions] */

	RodOD = 1.6;
	RodAngle = 35;

	/* [Hidden] */

	StemOD = 30.0; // max OD for valve-to-valve clearance

	BossOD = 16.0; // single-ended handle boss

	SlotWidth = 13.0;
	SlotHeight = 10.0;

	StemInset = 10.0;
	StemLength = StemInset + SlotHeight + 25.0;
	StemSides = 2*4;

	Align = 0180/StemSides; // 1 produces thinner jaw ends

	KnobOD1 = 70; // maximum dia without chamfer
	KnobOD2 = 60; // top dia

	KnobSides = 4*4;

	DomeHeight = 12; // dome shape above lobes

	KnobHeight = DomeHeight + 2*SlotHeight;

	DomeOD = KnobOD2 + (KnobOD1 – KnobOD2)*(DomeHeight/KnobHeight);

	DomeArcRad = (pow(KnobHeight,2) + pow(DomeOD,2)/4) / (2*DomeHeight);

	RodBCD = (StemOD + BossOD)/2;

	//- Adjust hole diameter to make the size come out right

	module PolyCyl(Dia,Height,ForceSides=0) { // based on nophead's polyholes

	Sides = (ForceSides != 0) ? ForceSides : (ceil(Dia) + 2);

	FixDia = Dia / cos(180/Sides);

	cylinder(r=(FixDia + HoleWindage)/2,h=Height,$fn=Sides);
	}

	//– Stem for valve handles

	module Stem() {

	difference() {
	rotate(Align)
	cylinder(d=StemOD,h=StemLength,$fn=StemSides);
	translate([0,0,SlotHeight/2 – Protrusion/2])
	cube([2*StemOD,SlotWidth,(SlotHeight + Protrusion)],center=true);
	translate([0,0,-Protrusion])
	cylinder(d=BossOD,h=SlotHeight,$fn=2*StemSides);
	if (RodHoles)
	for (i=[-1:1])
	rotate(i*RodAngle + 90)
	for (j=[-1,1])
	translate([j*RodBCD/2,0,-Protrusion])
	rotate(180/4)
	PolyCyl(RodOD,2*SlotHeight,4);
	}

	}


	//– Hand-friendly knob

	module KnobCap() {
	difference() {
	scale([1.0,0.75,1.0])
	rotate(180/KnobSides)
	intersection() {
	translate([0,0,(KnobHeight-DomeArcRad)])
	sphere(r=DomeArcRad,$fa=180/KnobSides);
	cylinder(r1=KnobOD1/2,r2=KnobOD2/2,h=KnobHeight,$fn=KnobSides);
	cylinder(r1=KnobOD2/2,r2=KnobOD1/2,h=KnobHeight,$fn=KnobSides);
	}
	translate([0,0,-Protrusion])
	rotate(Align)
	cylinder(d=(StemOD + 2*ThreadWidth),h=(StemInset + Protrusion),$fn=StemSides);
	}
	}

	//- Build it


	if (Layout == "Knob")
	KnobCap();

	if (Layout == "Stem")
	Stem();

	if (Layout == "Build") {
	translate([-KnobOD1/2,0,0])
	KnobCap();
	translate([StemOD/2,0,StemLength])
	rotate([180,0,0])
	Stem();
	}

	if (Layout == "Show") {
	translate([0,0,0])
	Stem();
	translate([0,0,StemLength – StemInset])
	KnobCap();
	}

view raw Hose Connector Knob.scad hosted with ❤ by GitHub

The New Hotness

Garden Hose Valve Wrench: Reinforced