The New Hotness

After three years, the retainer holding the front bathroom door open against winds blowing through the house on stormy days finally fractured, right at the top of the towel rack where you’d expect it:

Bathroom Door Retainer - fractured — Bathroom Door Retainer – fractured

I was all set to add reinforcing pins and whatnot, then came to my senses and just made the whole thing a few millimeters larger:

Bathroom Door Retainer - stronger — Bathroom Door Retainer – stronger

Customer feedback indicates white blends better with the background.

I made a few minor tweaks to the original design, including slightly larger bumps to hold it against the towel bar that, regrettably, put corresponding gouges into the bar. Who knew they used such soft plastic back in the day?

The OpenSCAD source code as a GitHub Gist:

	// Bathroom Door Retainer
	// Ed Nisley KE4ZNU – May 2017
	// 2020-07 beef up, particularly at top of bar

	Layout = "Show"; // [Show, Build]

	//——-
	//- Extrusion parameters must match reality!

	/* [Hidden] */

	ThreadThick = 0.20;
	ThreadWidth = 0.40;

	HoleWindage = 0.2;

	Protrusion = 0.1; // make holes end cleanly

	function IntegerMultiple(Size,Unit) = Unit * ceil(Size / Unit);

	//——-
	// Dimensions

	/* [Dimensions] */

	TowelBarSide = 20.5; // towel bar across flat side
	TowelBarAngle = 45; // rotation of top flat from horizontal
	BumpOD = 2.0; // retaining ball

	DoorOffset = 14.0; // from towel bar to door
	DoorThick = 37.0;

	WallThick = 8.0; // minimum wall thickness
	PlateThick = 4.0; // … slab

	RetainerDepth = 15.0; // thickness of retaining notch

	NumSides = 6*4;
	CornerRad = WallThick;

	BarClipOD = TowelBarSidesqrt(2) + 2WallThick;
	BarClipRad = BarClipOD/2;

	OAH = RetainerDepth + PlateThick;

	module LatchPlan() {

	union() {
	linear_extrude(height=OAH,convexity=4)
	difference() {
	union() {
	circle(d=BarClipOD,$fn=NumSides);
	hull()
	for (i=[0,1], j=[0,1])
	translate([i(BarClipRad + DoorOffset + DoorThick + WallThick – CornerRad),j(BarClipRad – CornerRad)])
	circle(r=CornerRad,$fn=4*4);
	}
	rotate(TowelBarAngle) // towel bar shape
	square(size=TowelBarSide,center=true);
	translate([0,-TowelBarSide/sqrt(2)]) // make access slot
	rotate(-TowelBarAngle)
	square(size=[2*TowelBarSide,TowelBarSide],center=false);
	}
	for (a=[0:180:360])
	rotate(a + TowelBarAngle)
	translate([TowelBarSide/2,0,OAH/2])
	rotate([90,0,45])
	sphere(d=BumpOD,$fn=4*3);
	}
	}

	module Latch() {

	difference() {
	LatchPlan();
	translate([BarClipRad + DoorOffset,-BarClipRad/2,-Protrusion])
	cube([DoorThick,BarClipOD,RetainerDepth + Protrusion],center=false);
	}
	}

	//——-
	// Build it!

	if (Layout == "Show") {
	Latch();
	}

	if (Layout == "Build") {
	translate([0,0,OAH])
	rotate([180,0,0])
	Latch();
	}

view raw Bathroom Door Retainer.scad hosted with ❤ by GitHub

Done!

The New Hotness

Bathroom Door Retainer: Bigger and Stronger