The New Hotness

Faced with a need to send documents rolled up in a tube, rather than folded flat, I sawed off a suitable length of cardboard tube from the heap, then discovered a distinct lack of end caps.

Well, once again, it’s 3D printing to the rescue:

Mailing Tube Cap - top - Slic3r — Mailing Tube Cap – top – Slic3r

The small ribs probably don’t actually do anything, but seemed like a nice touch.

They’re somewhat less boring from the bottom:

Mailing Tube Cap - bottom - Slic3r — Mailing Tube Cap – bottom – Slic3r

The fancy spider supports that big flat top and provides some crush resistance. The flat flange should collect the edge of the packing tape wrapped around the ends.

A firm shove installs them, so the size worked out perfectly:

Mailing tube end cap - installed — Mailing tube end cap – installed

Add a wrap of tape to each end, affix the USPS label, and they went out with the next day’s mail, PETG hair and all.

The OpenSCAD source code as a GitHub Gist:

	// Mailing tube end cap
	// Ed Nisley KE4ZNU – June 2017

	Layout = "Build";

	//- Extrusion parameters – must match reality!

	ThreadThick = 0.25;
	ThreadWidth = 0.40;

	function IntegerMultiple(Size,Unit) = Unit * ceil(Size / Unit);

	Protrusion = 0.1;

	HoleWindage = 0.2;

	//- Screw sizes

	inch = 25.4;

	TubeID = 2 * inch;
	TubeWall = 0.1 * inch;

	CapInsert = 15.0;
	CapRim = 1.0;
	CapWall = 3*ThreadWidth;

	NumFlanges = 3;
	FlangeHeight = 3*ThreadThick;
	FlangeWidth = ThreadWidth/2;
	FlangeSpace = CapInsert / (NumFlanges + 1);

	OAHeight = CapInsert + CapRim;

	NumRibs = 3*4;
	NumSides = 3*NumRibs;

	//- Adjust hole diameter to make the size come out right

	module PolyCyl(Dia,Height,ForceSides=0) { // based on nophead's polyholes

	Sides = (ForceSides != 0) ? ForceSides : (ceil(Dia) + 2);

	FixDia = Dia / cos(180/Sides);

	cylinder(r=(FixDia + HoleWindage)/2,h=Height,$fn=Sides);
	}

	module TubeCap() {

	difference() {
	cylinder(d=TubeID,h=OAHeight,$fn=NumSides);
	translate([0,0,CapWall])
	cylinder(d=TubeID – 2*CapWall,h=OAHeight,$fn=NumSides);
	}

	for (i=[1:NumFlanges])
	translate([0,0,i*FlangeSpace])
	difference() {
	cylinder(d=TubeID + 2*FlangeWidth,h=FlangeHeight,$fn=NumSides);
	translate([0,0,-Protrusion])
	cylinder(d=TubeID – 2CapWall,h=FlangeHeight + 2Protrusion,$fn=NumSides);
	}

	for (i=[0:NumRibs-1])
	rotate(i*360/NumRibs)
	translate([0,-ThreadWidth,CapWall + ThreadThick])
	cube([TubeID/2 – CapWall/2,2*ThreadWidth,CapInsert + CapRim – CapWall – ThreadThick],center=false);

	translate([0,0,CapInsert]) {
	difference() {
	cylinder(d=TubeID + 2*TubeWall,h=CapRim,$fn=NumSides);
	translate([0,0,-Protrusion])
	cylinder(d=TubeID – 32CapWall,h=2*CapRim,$fn=NumSides);
	}
	}
	}

	//- Build things

	if (Layout == "Show")
	TubeCap();

	if (Layout == "Build")
	translate([0,0,OAHeight])
	rotate([180,0,0])
	TubeCap();

view raw Mailing Tube Cap.scad hosted with ❤ by GitHub

The New Hotness

Mailing Tube End Caps