The New Hotness

A battery holder for AA alkaline cells descends directly from the NP-BX1 version:

Astable Multivibrator - Alkaline Batteries - solid model - Show layout — Astable Multivibrator – Alkaline Batteries – solid model – Show layout

The square recesses fit single contact pads on the left and a “positive-to-negative conversion” plate on the right, all secured with dabs of acrylic adhesive:

Alkaline AA holder - contacts — Alkaline AA holder – contacts

Although the OpenSCAD code contains an array of battery dimensions, it only works for AA cells.

The recess on the far left is where you solder the wires onto the contact tabs, with the wires leading outward through the holes in the lid. The case needs an indexing feature to hold the lid square while gluing it down.

Alkaline cells cells do not have current-limiting circuitry, so a low-current PTC fuse seems like a Good Idea. I initially thought of hiding it in the recess, but the Brutalist nature of the astables suggests open air.

The OpenSCAD source code as a GitHub Gist:

	// Astable Multivibrator
	// Holder for Alkaline cells
	// Ed Nisley KE4ZNU August 2020

	/* [Layout options] */

	CellName = "AA"; // [AA] — does not work with anything else
	NumCells = 2;

	Layout = "Case"; // [Build,Show,Lid]

	Struts = -1; // [0:None, -1:Dual, 1:Quad]

	// Extrusion parameters – must match reality! */

	/* [Hidden] */

	ThreadThick = 0.25;
	ThreadWidth = 0.40;

	HoleWindage = 0.2;

	function IntegerMultiple(Size,Unit) = Unit * ceil(Size / Unit);
	function IntegerLessMultiple(Size,Unit) = Unit * floor(Size / Unit);

	Protrusion = 0.1; // make holes end cleanly

	inch = 25.4;

	//- Basic dimensions

	WallThick = IntegerMultiple(3.0,ThreadWidth);
	CornerRadius = WallThick/2;

	FloorThick = IntegerMultiple(3.0,ThreadThick);

	TopThick = IntegerMultiple(2.0,ThreadThick);

	WireOD = 1.7; // wiring from pins to circuitry

	Gap = 5.0;

	// Cylindrical cell sizes
	// https://en.wikipedia.org/wiki/List_of_battery_sizes#Cylindrical_batteries

	CELL_NAME = 0;
	CELL_OD = 1;
	CELL_OAL = 2;

	CellData = [
	["AAAA",8.3,42.5],
	["AAA",10.5,44.5],
	["AA",14.5,50.5],
	["C",26.2,50],
	["D",34.2,61.5],
	["A23",10.3,28.5],
	["CR123A",17.0,34.5],
	["18650",18.8,65.2], // bare 18650 with button end
	["18650Prot",19.0,70.0], // protected 18650 = 19670 plus a bit
	];

	CellIndex = search([CellName],CellData,1,0)[0];
	echo(str("Cell index: ",CellIndex," = ",CellData[CellIndex][CELL_NAME]));

	//- Contact dimensions

	CONTACT_NAME = 0;
	CONTACT_WIDE = 1;
	CONTACT_HIGH = 2;
	CONTACT_THICK = 3; // plate thickness
	CONTACT_TIP = 4; // tip to rear face
	CONTACT_TAB = 5; // solder tab width

	ContactData = [
	["AA+",12.2,12.2,0.3,1.7,3.5], // pos bump
	["AA-",12.2,12.2,0.3,5.0,3.5], // half-compressed neg spring
	["AA+-",28.2,12.2,0.3,5.0,0], // pos-neg bridge

	["Li+",18.5,16.0,0.3,2.8,5.5],
	["Li-",18.5,16.0,0.3,6.0,5.5],
	];

	function ConDat(name,dim) = ContactData[search([name],ContactData,1,0)[0]][dim];

	ContactRecess = 2*ConDat(str(CellName,"+"),CONTACT_THICK);
	ContactOC = CellData[CellIndex][CELL_OD];

	WireBay = 6.0; // room for wiring to contacts

	//- Wire struts

	StrutDia = 1.6; // AWG 14 = 1.6 mm
	StrutSides = 3*4;

	ID = 0;
	OD = 1;
	LENGTH = 2;

	StrutBase = [StrutDia,StrutDia + 25ThreadWidth, // ID = wire, OD = buildable
	FloorThick + CellData[CellIndex][CELL_OD]]; // base is flush with cell top

	//- Holder dimensions

	BatterySize = [CellData[CellIndex][CELL_OAL] + // cell
	ConDat(str(CellName,"+"),CONTACT_TIP) + // pos contact
	ConDat(str(CellName,"-"),CONTACT_TIP) – // neg contact
	2*ContactRecess, // sink into wall
	NumCells*CellData[CellIndex][CELL_OD],
	CellData[CellIndex][CELL_OD]
	];

	echo(str("Battery space: ",BatterySize));

	CaseSize = [3*WallThick + // end walls + wiring partition
	BatterySize.x + // cell
	WireBay, // wiring bay
	2*WallThick + BatterySize.y,
	FloorThick + BatterySize.z
	];

	BatteryOffset = (CaseSize.x – (2*WallThick +
	CellData[CellIndex][CELL_OAL] +
	ConDat(str(CellName,"-"),CONTACT_TIP))
	) /2 ;

	ThumbRadius = 0.75 * CaseSize.z;


	StrutOC = [IntegerLessMultiple(CaseSize.x – 2CornerRadius -2StrutBase[OD],5.0),
	IntegerMultiple(CaseSize.y + StrutBase[OD],5.0)];

	StrutAngle = atan(StrutOC.y/StrutOC.x);

	echo(str("Strut OC: ",StrutOC));

	LidSize = [2*WallThick + WireBay + ConDat(str(CellName,"+"),CONTACT_THICK), CaseSize.y, FloorThick/2];


	//———————-
	// Useful routines

	module PolyCyl(Dia,Height,ForceSides=0) { // based on nophead's polyholes

	Sides = (ForceSides != 0) ? ForceSides : (ceil(Dia) + 2);

	FixDia = Dia / cos(180/Sides);

	cylinder(r=(FixDia + HoleWindage)/2,h=Height,$fn=Sides);
	}



	//– Overall case with origin at battery center

	module Case() {

	difference() {
	union() {
	hull()
	for (i=[-1,1], j=[-1,1])
	translate([i*(CaseSize.x/2 – CornerRadius),
	j*(CaseSize.y/2 – CornerRadius),
	0])
	cylinder(r=CornerRadius/cos(180/8),h=CaseSize.z,$fn=8); // cos() fixes undersize spheres!

	if (Struts)
	for (i = (Struts == 1) ? [-1,1] : -1) { // strut bases
	hull()
	for (j=[-1,1])
	translate([iStrutOC.x/2,jStrutOC.y/2,0])
	rotate(180/StrutSides)
	cylinder(d=StrutBase[OD],h=StrutBase[LENGTH],$fn=StrutSides);

	translate([i*StrutOC.x/2,0,StrutBase[LENGTH]/2])
	cube([2*StrutBase[OD],StrutOC.y,StrutBase[LENGTH]],center=true); // blocks for fairing

	for (j=[-1,1]) // hemisphere caps
	translate([i*StrutOC.x/2,
	j*StrutOC.y/2,
	StrutBase[LENGTH]])
	rotate(180/StrutSides)
	sphere(d=StrutBase[OD]/cos(180/StrutSides),$fn=StrutSides);

	}
	}

	translate([BatteryOffset,0,BatterySize.z/2 + FloorThick]) // cells
	cube(BatterySize + [0,0,Protrusion],center=true);

	translate([BatterySize.x/2 + BatteryOffset + ContactRecess/2 – Protrusion/2, // contacts
	0,
	BatterySize.z/2 + FloorThick])
	cube([ContactRecess + Protrusion,
	ConDat(str(CellName,"+-"),CONTACT_WIDE),
	ConDat(str(CellName,"+-"),CONTACT_HIGH)
	],center=true);

	translate([-(BatterySize.x/2 – BatteryOffset + ContactRecess/2 – Protrusion/2),
	ContactOC/2,
	BatterySize.z/2 + FloorThick])
	cube([ContactRecess + Protrusion,
	ConDat(str(CellName,"+"),CONTACT_WIDE),
	ConDat(str(CellName,"+"),CONTACT_HIGH)
	],center=true);

	translate([-(BatterySize.x/2 – BatteryOffset + ContactRecess/2 – Protrusion/2),
	-ContactOC/2,
	BatterySize.z/2 + FloorThick])
	cube([ContactRecess + Protrusion,
	ConDat(str(CellName,"-"),CONTACT_WIDE),
	ConDat(str(CellName,"-"),CONTACT_HIGH)
	],center=true);

	translate([-CaseSize.x/2 + WireBay/2 + WallThick, // wire bay
	0,
	BatterySize.z/2 + FloorThick + Protrusion/2])
	cube([WireBay,
	BatterySize.y,
	BatterySize.z + Protrusion
	],center=true);

	for (j=[-1,1])
	translate([-(BatterySize.x/2 – BatteryOffset + WallThick/2), // contact tabs
	j*ContactOC/2,
	BatterySize.z + FloorThick – Protrusion])
	cube([2*WallThick,
	ConDat(str(CellName,"+"),CONTACT_TAB),
	(BatterySize.z – ConDat(str(CellName,"+"),CONTACT_HIGH))
	],center=true);

	if (false)
	translate([0,0,CaseSize.z]) // finger cutout
	rotate([90,00,0])
	cylinder(r=ThumbRadius,h=2*CaseSize.y,center=true,$fn=22);

	if (Struts)
	for (i2 = (Struts == 1) ? [-1,1] : -1) { // strut wire holes and fairing
	for (j=[-1,1])
	translate([i2StrutOC.x/2,jStrutOC.y/2,FloorThick])
	rotate(180/StrutSides)
	PolyCyl(StrutBase[ID],2*StrutBase[LENGTH],StrutSides);

	for (i=[-1,1], j=[-1,1]) // fairing cutaways
	translate([iStrutBase[OD] + (i2StrutOC.x/2),
	j*StrutOC.y/2,
	-Protrusion])
	rotate(180/StrutSides)
	PolyCyl(StrutBase[OD],StrutBase[LENGTH] + 2*Protrusion,StrutSides);
	}

	}
	}


	module Lid() {

	difference() {
	hull()
	for (i=[-1,1], j=[-1,1], k=[-1,1])
	translate([i*(LidSize.x/2 – CornerRadius),
	j*(LidSize.y/2 – CornerRadius),
	k*(LidSize.z – CornerRadius)]) // double thickness for flat bottom
	sphere(r=CornerRadius/cos(180/8),$fn=8);

	translate([0,0,-LidSize.z]) // remove bottom
	cube([(LidSize.x + 2Protrusion),(LidSize.y + 2Protrusion),2*LidSize.z],center=true);

	for (j=[-1,1]) // wire holes
	translate([0,j*LidSize.y/4,-Protrusion])
	PolyCyl(WireOD,2*LidSize.z,6);

	}
	}


	//——————-
	// Build it!

	if (Layout == "Case")
	Case();

	if (Layout == "Lid")
	Lid();

	if (Layout == "Build") {
	rotate(-90)
	translate([CaseSize.x/2 + Gap,0,0])
	Case();
	rotate(-90)
	translate([-LidSize.x/2 – Gap,0,0])
	Lid();
	}

	if (Layout == "Show") {
	Case();
	translate([-CaseSize.x/2 + LidSize.x/2,0,(CaseSize.z + Gap)])
	Lid();
	}

view raw Astable Multivibrator – Alkaline Batteries.scad hosted with ❤ by GitHub

The New Hotness

AA Alkaline Battery Holder