Laser Cutter: Improving the Red-Dot Pointer

The red-dot pointer on the OMTech laser cutter has the same problem as my laser aligner for the Sherline mill: too much brightness creating too large a visual spot. In addition, there’s no way to make fine positioning adjustments, because the whole mechanical assembly is just a pivot.

The first pass involved sticking a polarizing filter on the existing mount while I considered the problem:

OMTech red dot pointer - polarizing filter installed
OMTech red dot pointer – polarizing filter installed

The red dot pointer module is 8 mm OD and the ring is 10 mm ID, but you will be unsurprised to know the laser arrived with the module jammed in the mount with a simple screw. Shortly thereafter, I turned the white Delrin bushing on the lathe to stabilize the pointer and installed a proper setscrew, but it’s obviously impossible to make delicate adjustments with that setup.

Making the polarizing filter involves cutting three circles:

OMTech red dot pointer - polarizing filter
OMTech red dot pointer – polarizing filter

Rotating the laser module in the bushing verified that I could reduce the red dot to a mere shadow of its former self, but it was no easier to align.

Replacing the Delrin bushing with a 3D printed adjuster gets closer to the goal:

Pointer fine adjuster - solid model
Pointer fine adjuster – solid model

Shoving a polarizing filter disk to the bottom of the recess, rotating the laser module for least brightness, then jamming the module in place produces a low-brightness laser spot.

The 8 mm recess for the laser module is tilted 2.5° with respect to the Y axis, so (in principle) rotating the adjuster + module (using the wide grip ring) will move the red dot in a circle:

Improved red-dot pointer - overview
Improved red-dot pointer – overview

The dot sits about 100 mm away at the main laser focal point, so the circle will be about 10 mm in diameter. In practice, the whole affair is so sloppy you get what you get, but at least it’s more easily adjusted.

The M4 bolt clamping the holder to the main laser tube now goes through a Delrin bushing. I drilled out the original 4 mm screw hole to 6 mm to provide room for the bushing:

Improved red-dot pointer - drilling bolt hole
Improved red-dot pointer – drilling bolt hole

The bushing has a wide flange to soak up the excess space in the clamp ring:

Improved red-dot pointer - turning clamp bushing
Improved red-dot pointer – turning clamp bushing

With all that in place, the dimmer dot is visually about 0.3 mm in diameter:

Improved red-dot pointer - offset
Improved red-dot pointer – offset

The crappy image quality comes from excessive digital zoom. The visible dot on the MDF surface is slightly larger than the blown-out white area in the image.

The CO₂ laser hole is offset from the red laser spot by about 0.3 mm in both X and Y. Eyeballometrically, the hole falls within the (dimmed) spot diameter, so this is as good as it gets. I have no idea how durable the alignment will be, but it feels sturdier than it started.

Because the red dot beam is 25° off vertical, every millimeter of vertical misalignment (due to non-flat surfaces, warping, whatever) shifts the red dot position half a millimeter in the XY plane. You can get a beam combiner to collimate the red dot with the main beam axis, but putting more optical elements in the beam path seems like a Bad Idea™ in general.

The OpenSCAD source code as a GitHub Gist:

// Laser cutter red-dot module fine adjust
// Ed Nisley KE4ZNU 2022-09-22
Layout = "Show"; // [Build, Show]
/* [Hidden] */
ThreadThick = 0.25;
ThreadWidth = 0.40;
HoleWindage = 0.2;
Protrusion = 0.1; // make holes end cleanly
inch = 25.4;
ID = 0;
OD = 1;
function IntegerMultiple(Size,Unit) = Unit * ceil(Size / Unit);
// Dimensions
PointerOD = 8.0 + 0.2; // plus loose turning fit
Aperture = 5.0; // clear space for lens
SkewAngle = 2.5;
MountRing = [10.0,16.0,8.0]; // OEM laser module holder
GripRim = [Aperture,MountRing[OD] + 2*1.5,3.0]; // finger grip around OD
NumSides = 24;
// Useful routines
module PolyCyl(Dia,Height,ForceSides=0) { // based on nophead's polyholes
Sides = (ForceSides != 0) ? ForceSides : (ceil(Dia) + 2);
FixDia = Dia / cos(180/Sides);
cylinder(r=(FixDia + HoleWindage)/2,
// Holder geometry
module Holder() {
difference() {
union() {
PolyCyl(MountRing[ID],MountRing[LENGTH] + GripRim[LENGTH],NumSides);
translate([0,0,-Protrusion]) // close enough without skew angle
translate([0,0,MountRing[LENGTH]/2 + GripRim[LENGTH]])
// Build it
if (Layout == "Show") {
if (Layout == "Build") {